Boldenone Undecylenate Equipoise 200mg/ml recipe:
Equipoise 200mg/mL …….1000mL
200gram Boldenone Undecylenate
20mL BA (Benzyl alcohol )
180mL BB (Benzyl benzoate)
630mL GSO (Grapeseed Oil)
Boldenone Undecylenate 200mg/ml recipe:
Equipoise 200mg/ml@ 50ml
10g Boldenone Undeclynate Powder
7.5ml of Benzyl Benzoate
2.5ml of Benzyl Alcohol
32ml of your favourite Oil
2 18ga needles, 1 25ga Needle
0.45 Sterile Whatman Filter
50ml Sterile Vial
Rubbing Alchol/Paper Towels
The steps to make Equipoise 200mg/ml:
1: take out scale (i like to calibrate it every use) and put on unsterile 50ml vial on scale and zero out.
2: Draw up 12ml of Eq using 12ml syringe, make sure there are no airbubbles and plunger is exactly in linewith 12ml hatch mark. Now slowly squirt eq into vial until scale says 10.0 grams. For me this is usually exactly 10ml so 1g has 1 mL displacement. Also add the 7.5ml of bb and 2.5ml of ba
3: Now add 30 of the 32ml of oil into the vial to make total volume of oil/ba/bb/hormone to be 50 mL. Leave the 2ml of oil in syringe for later use. Put rubber stopper into vial aswell as one of the 18ga needles. Boil a pot of hot water and then remove from heat and put vial into pot for 10 minutes, take out after 5 to shake and put back in.
4: I have a crimper so i crimp another seal on the vial but you could also duct tape it on so that rubber
stopper doesn't come out when upside down when you're drawing oil out of vial. Here's what it looks like
unfiltered but mixed up.
5: Now take out sterile 50ml vial and wipe stopper with rubbing alchol. Put 18ga needle and 25ga needle
through stopper, and attach whatman filter to the 18ga needle stuck in vial.
6: Once you've filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter. This is what final product will look like. Notice i left 25ga pin in.
7: Once you've filtered all 50ml and vial is totally empty, take the last 2ml you had saved and run it through the filter to get all gear out of it and only leave plain oil in the filter. This is what final product will look like. Notice i left 25ga pin in.
8: Now put vial in oven at 200 degrees F, and bake for 15 minutes. Some repeat this step more than once but i never have and not had a problem. There you go, save yourself a ton of cash and MAKE YOUR OWN GEAR!
Boldenone Undecylenate Equipoise 200mg/ml info:
Drug Class: Anabolic /Androgenic steroid
Applications: Quality, Competitive / diet, mass
Anabolic components: strong
Androgenic components: medium
Category: Injectable Steroids.
Hobby: 400-600mg/ Week
Professional range: 600-1000mg/Week
Application period: 12 weeks to 6 months
Active Life: 14-16 days
Average Reported Dosage: Men 400-600 mg/week; Women 50-150 mg/week
Water Retention: Low
High Blood Pressure: Rare
Aromatization: About 50% less than testosterone
Liver Toxic: None
DHT Conversion: Low
Decreases HPTA function: Moderately (Dose dependent)
Water Retention: Low
Usage:for cutting and bulking cycles and fat loss
Five advantages of making finished steroids by yourself:
1.The cost is only 40-60% of the normal cost
2.They take only a short time to prepare
3.They are easier and cheaper to ship than amps or vials
4.Less chance of your order getting seized by customs
5.Unlike vials and amps, they come with a refund/reship policy
1) Best prices with satisfied quality.
2) Rich experienced in delivering the parcels to you.
3) Enough stock ensure the prompt delivery time.
4) Good after-sales service.
5) Package will be reshipped if sent failed.
6) Specials are possible when the order is big enough.
The Related products you may need:
|Steroids for bulking cycle
||Steroids for cutting cycle
||Steroids for Fat Loss
||Masteron (Drostanolone Propionate)
||Primobolan (Methenolone Acetate)
||Primobolan Depot (Methenolone Enanthate)
||Oral Turinabol (4-Chlorodehydromethyltestosterone)
||testosterone, Enanthate, Cypionate, Propionate, Sustanon-250 etc.